enEnglish

What is a data communication system?

Nov 27, 2025

Leave a message

What is a data communication system?

 

CAN bus communication

 

The Controller Area Network (CAN) bus is a serial communication protocol bus designed for real-time applications. It can transmit signals over twisted pair, coaxial cable, or optical fiber. Thanks to its high performance, high reliability, and excellent real-time characteristics, CAN has become one of the most widely adopted fieldbuses worldwide.

 

Currently, CAN communication is the mainstream communication method for battery management systems (BMS). It is strongly recommended and widely implemented in both domestic and international standardized electric vehicle battery management systems, as well as in relevant BMS data communication standards both in China and abroad. Other bus protocols such as RS232 and RS485 are also used in some internal communications of battery management systems.

 

CAN bus communication

 

FlexRay Communication

 

With the development of automotive electronic technology, traditional CAN solutions are no longer the optimal choice for addressing vehicle communication challenges. In September 2000, BMW and DaimlerChrysler, in collaboration with Philips and Motorola, established the FlexRay Consortium to develop a new communication protocol and promote it as the standard protocol for advanced powertrain, chassis, and X-by-wire systems.

FlexRay offers numerous advanced features that traditional in-vehicle communication protocols (such as CAN) do not possess, including:

 

(1) High Transmission Rate Each FlexRay channel provides a bandwidth of 10 Mbit/s. FlexRay can operate as a single-channel system (similar to CAN or LIN networks) or as a dual-channel system, achieving a maximum transmission rate of 20 Mbit/s-20 times higher than the maximum operating speed of current CAN networks.

 

(2) Synchronized Time Base The access method used in FlexRay is based on a synchronized global time base. This time base is automatically established and synchronized by the protocol and made available to the application layer. The precision of the time base ranges between 0.5 μs and 10 μs (typically 1–2 μs).

 

(3) Deterministic Communication Communication in FlexRay occurs in continuously repeating communication cycles, where specific messages are assigned fixed positions (slots) within the cycle. As a result, the receiver knows in advance exactly when a message will arrive. The temporal deviation of message arrival times is extremely small and guaranteed.

 

(4) High Fault Tolerance Strong error detection capabilities and fault-tolerant operation are key design considerations in FlexRay.

  • The FlexRay bus employs Cyclic Redundancy Check (CRC) to detect communication errors.
  • Through dual-channel communication, FlexRay provides redundancy.
  • By using a star topology (or a combination of topologies), FlexRay can fully address fault-tolerance requirements, including single-point-of-failure mitigation.

 

(5) Flexibility Flexibility was a primary focus during the development of the FlexRay protocol and is reflected in the following aspects: ① Supports multiple network topologies (bus, star, hybrid, etc.); ② Configurable message length: the data payload length can be tailored to the specific requirements of the control application; ③ When using dual-channel topology, the two channels can either be used to increase bandwidth or to transmit redundant messages; ④ The duration of the static and dynamic segments within a communication cycle can be adjusted according to the specific application needs.

 

FlexRay Communication

 

Industrial Ethernet

 

Industrial Ethernet is a fully open, fully digital network. Devices from different manufacturers can easily achieve interconnection by complying with standard network protocols. It offers high communication rates: Fast Ethernet with speeds of 10 Mbit/s and 100 Mbit/s has been widely adopted, Gigabit Ethernet technology has matured, and 10 Gbit/s Ethernet is under active research and development. These rates are significantly higher than those of current fieldbuses.

 

However, industrial Ethernet still faces several challenges, primarily including:

  • Real-time performance
  • Adaptability and reliability in harsh industrial environments
  • Availability of application-layer protocols suitable for industrial automation control

With the continuous advancement of industrial Ethernet technology, the above issues are being progressively resolved.

 

Industrial Ethernet

Send Inquiry